Dingxin Films has a professional construction process, to ensure that your paint protection film can be well pasted, will not be wasted, today we will give you an analysis of the professional construction process of Dingxin Films shop.
- Match the invisible livery
We will collect photos of the original vehicle of the relevant construction management vehicle from you, photos of the front, side, rear, vehicle, and nameplate information, and the radar, water nozzle, trailer cover, and reflective lights on the front fender on the bumper must be clearly displayed. Consult the person in charge to obtain the data analysis information provided by the vehicle for the use of the special car.
- Inspect the vehicle
Carefully inspect the paint surface of the construction vehicle, record it after the inspection, and confirm and sign it by the owner before the construction can be carried out.
Prepare for construction.
Prepare the objects required for the film: transparent film public scraper, cloth, public watering can, check the construction environment, the construction is extremely dangerous in the ventilation environment, the blocked air conditioning constant temperature environment is the condition for the transparent film (the construction environment is controlled at 20-25 degrees is the best, the temperature is too high, the water evaporation is too fast to affect the construction effect, the temperature is too low, the transparent film will be harder to increase the difficulty of construction), and of course, there are bright lights.
- Paint pre-treatment
After receiving the car, the whole car should be controlled to wash once, the time cost of fine washing is two or three times more than our usual time, mainly through the cleaning of the target for paint, rubber strips, sheet metal edge seams, etc., to maintain patience to rinse. The whole car is sprayed with green cleaning agent (the stubborn stains on the paint surface can be removed in depth, so as to improve the hydrophilicity required by the construction technology, so that the protective film and the paint surface can achieve a better bonding), and the paint depth data cleaning is carried out with car wash mud while cleaning the paint surface by hand until there is no sand grain, (for the paint surface is relatively simple and rough, the car wash mud can not be processed in time The green cleaning agent can be handled more easily) Finally, the air gun blows the sheet metal edge seam position No sand will have problems. The degree of environmental cleanliness of the paint surface is directly related to the construction of this step and the key to its development.
- Formal construction
Before applying the film, clean the paint surface. In the case of lighting, the paint surface is carefully checked, especially pay attention to the hood, back cover and other three-dimensional premises, the film process in the larger area of 3 people to achieve, 2 to take the film, 1 person to spray the installation fluid, the area of the smaller 2 people can complete the film process, the most professional technician single person can be constructed.
- Construction wiping
Before scraping the water, gently touch the surface of the car coat with your hands, so that the installation fluid (and the adhesive will not affect the development of any chemical change, can achieve different levels of national safety production drinking) make full use of the coverage of each area of the car coat, the car coat looks like we do not have large bubbles for the best, in the process of water management, first confirm the position of the center line, and then rush to both sides of the water. Halfway to the time there will be a need for a large amount of installation fluid, this work with the hands of the excess installation fluid to the place that has not been scraped, this process design can be confirmed again whether the installation fluid is sprayed in place, the process of rushing the water must be closely watched to scrape the place whether there is a problem, such as the surface of the water can not see the installation of the car coat "installation completion, wiping steps are too messy. After the wiping is completed, wipe the surface quality of the car jacket with a towel, and check whether it is qualified during the installation process before the water has evaporated. If you find a problem, you need to restart the installation in time.
- Edging
The position that needs to be edging needs to be sprayed with water, and the excess installation liquid should be rinsed clean, and the alcohol and water can be quickly evaporated to form the glue of the film, so that the glue of the film can return to the original viscosity. Depending on the environment and temperature, the edging work can be carried out in 1-3 hours, if it is found that there is still water in the membrane, and the edge cannot be wrapped, the spraying process of alcohol water should be reused. After the hemming is completed, it is necessary to carry out a detailed inspection of the edge seams in all these places that have been installed, and the inspection time of this process is 2-4 hours.
- Apply the solution
Apply the packaging solution (filler film surface coating) evenly over the protective film and do not apply it in the corners.
- Quality inspection and delivery
After the installation is completed, the construction vehicle is parked in a place with strong light, and the quality inspection personnel are not the construction personnel at that time, and other relevant personnel should be arranged to conduct a detailed inspection. If there is a problem, it must be clearly pointed out and solved in a timely and effective manner before the car can be delivered.
When handing over the car, please record the customer information in detail, apply for electronic warranty, and pay attention to inform the customer of the use of the product during use.
- Routine maintenance
Use Dingxin Films membrane cleaning solution (super strong decontamination treatment function) to spray on the membrane surface after soaking for 10-15 minutes, continue to spray white cleaning agent and combine with nano sponge scrubbing, after cleaning, you can use the encapsulant for a brightness sealing.
